Technical description BRF building - STANDARD

Technical description

Budapart residential building ”F”

  1. General description of the building


Monolithic reinforced concrete base plate, which rests on pile foundation.

Load-bearing structure:

The building is constructed of partly using the tradition construction method, with reinforced concrete and brick filling walls, and  pre-fabricated wall panels.

Floor slabs:

Monolithic reinforced concrete floor slabs with acoustically dimensioned so-called floating layer providing sound insulation for the noise of steps.


Basement walls, surrounding walls of staircases and the required reinforcing walls are made of monolithic reinforced concrete or pre-fabricated wall panels. Elevator shafts are made with reinforced concrete walls. Perimeter walls are pre-fabricated reinforced concrete panel walls  typically including thermal insulation equipped with reinforced concrete slab sheet surface finish. Where statically required, reinforced concrete walls are made on the façade and in the interior areas, the reinforcing walls on the external façade are pre-fabricated reinforced concrete sandwich panelled walls linked with rigid connection. Separating walls within the apartment are made with installed plasterboard structure, 2x2 layer plasterboard covering, in wet rooms with impregnated plasterboard filled with rock wool in the entire cross-section, witha total thickness of 10 cm. Apartment separating walls (apartment-to-passageway, apartment-to-apartment) are made of acoustically dimensioned building blocks.


The buildings with isolated plate roof are made with waterproof PVC, rubber or bituminous plates, where partial green roofs or tiled areas will be established.


Terraces opened to the internal garden have paving stone, ceramic, installed or glued covering, the upper terraces, loggias, balconies are covered with anti-slip freeze-resistant ceramic tiles. Balcony balustrades are made of ironwork, glazing or solid  according to the architect’s plans.

External doors and windows:

The windows and balcony doors are made of modern plastic profile system, with 3 layered thermal insulating glazing pane, with exquisite air tightness. Trickle vents are located on at least two windows and doors in every apartment. The design of façade doors and windows have a shutter case, a shutter, with manual movement in the basic design, optionally in motor-operated design, with a guide track suitable to receive a mosquito net next to the case. For the doors and windows higher than 2.5 m only plisse mosquito net can be installed.


The façade of the buildings has a range of colours and surface finish, with the appearance of facing plaster and also the pre-fabricated thermal-insulated reinforced concrete sandwich element fitted with an external slab according to architect’s plans.

Interior plasters:

Depending on the type, the walls receive thin plaster/smoothing, the ceilings are made without plaster, but with a smoothing.

Elevators, corridors:

Silent and modern elevators are installed in the buildings. The indoor garage gate is operated by remote controller. Fireproof steel doors – according to the regulations - are installed between the indoor garage and the staircases. Common areas, staircases and corridors are finished with modern resin floor cover or stone-ceramic floor-tiles.

Building engineering systems:

The heating energy is provided by a district heating provider, with centralized hot water production and individual sub meters for each apartment. Heating can be regulated for each apartment, the cost is divided based on data collected by individual sub meters.

The building also produces centralised cooling energy, which can also be regulated individually for each apartment. The settlement of consumption also happens based on data collected by individual sub meters.

Extract fans are installed in baths and toilets where natural ventilation is not provided. Kitchen extract fans are connected to a pipe system with non-return valve.

The sewage pipe- and the rainwater pipe system are in a separate system and driven within a separated system into the public sewers.


The in-house distributors and electrical power consumption meters are placed in electrical switch room or grouped at electrical cabinets on each floor. The electrical cabling system – copper wires - in the apartments are placed in sheath tube installed inside the walls. At the basement the wires are led in cable plates or outside of the walls.

Motion controlled lamps fitted with the protection according to the regulations are placed in the common areas.

Lamps with twilight sensor are used at the building entrances.

At the building entrances and in few places at the common areas video camera security system with digital recording option is installed,

The digital main entrance phone intercom, with door opening option are fitted with an outside unit, while in the apartments an audio phone intercom is mounted. At the customer’s request the interior units can be replaced with a video unit.


The minimum internal height in the storages is 1.9 meters. In storages it is possible that mechanical, electrical wires and possibly fittings not directly affecting this property will be routed in the area above the free internal height. Floors are typically smoothed concrete or other surfaces suitable for cleaning. The storage room can be locked, the door and window structure is a locksmith or joinery structure.

Car parking spot:

Its floor is typically smoothed concrete or other surfaces suitable for cleaning. Above and in the surroundings of the parking spot, there may be mechanical, electrical wiring, fittings, equipment that do not block the intended use.

  1. General technical specifications for the apartments


Interior design of the apartments: wall and floor tiles, bath tubs, shower stalls, sanitary equipment and internal doors can be selected from the standard collection and we offer the possibility to choose from different categories until a certain deadline, specified in the sale and purchase contract, in case the date of the contract does not lapse the deadline of the product (e.g. tiles) selection.

Internal height:

The average height in the residence rooms of the apartments is typically 2.85 m, except for rooms with installed suspended ceiling. Connections of the heating system of the ceiling are placed out in one point of the apartment (typically through the ceiling of the lobby and the joint wardrobe), next to it there is a distributor-collector fitting, installed to the ceiling. To cover the engineering elements in these rooms, monolithic plasterboard suspended ceiling is made, the useful clear height in these rooms is 2.55 m. To ensure the maintenance of the engineering elements a revision opening is made in white into the suspended ceiling.

Apartment entrance doors:

Apartment entrances are fitted with entrance doors with MABISZ certification and central lock with several locking point, with viewer optic.

Interior doors:

Interior doors are curved or angular edged folded , semi-solid flush doors with solid door leaves, with frame to be installed afterwards. Doors are with nominal height of ~210 cm, with metal handle. Optionally you can ask for a version with glass panel.

Floor and wall tiles:

Sanitary rooms are paved with first class wall tiles until the height of the door frame, finished with uncut tile. (The exact height depends on the chosen tile type.)  in sanitary rooms. Ceramic tiles between upper and lower kitchen cabinets are placed in 60cm height. All positive joints are protected with plastic edge. Sanitary rooms have first class ceramic floor tiles. Kitchens are fitted with warm flooring as standard. Terraces are tiled with a material selected by the architect in order to keep the uniform façade look.

Laminated parquet floor:

First class laminate parquet flooring, with transition strips where required.

Floor and wall tiles:

First class glazed or gres ceramic tiles.

Surface dressing:

White dispersion paint is applied to the internal walls of the apartments. The ceilings are painted with white dispersion paint over skimmed surface.


Apartments are handed over with built-in kitchen furniture with upper and lower cabinets equipped with kitchen machinery: electric hotplate and oven, kitchen extractor fan and sink with faucet. (The position of the fridge is shown on the layout, but it does not include in the standard fixtures.)

The different apartments are equipped with the following number of kitchen cabinets:

Studios and one bedroom apartments 5 lower cabinets

Two bedroom apartments         6 lower cabinets

Three bedroom apartments      7 lower cabinets

The kitchen units will be fitted with a stainless steel sink with basin, with a tap of the type offered by the Seller.

Sanitary equipment:

For all apartments, washing machine connections are built in bathrooms (or another room marked on the plan, e.g. laundry room) and dishwasher electric-, water- and sewage- connection are built in the kitchens. Toilets are built-in types with dual function push button.


Apartments are fitted with ceiling heating, which provides high comfort and radiators are not taking up living space. All rooms can be regulated individually. Heating can be controlled by a thermostat in the rooms. Bathrooms have       towel dryers with electric heating inlet.


Using the pipes of the heating system, which are installed in the ceiling, the cooling of the apartments is provided as a basic feature. The system provides high comfort, since no individual indoor and outdoor appliances are

needed, so the operation is completely wind- and noise free. The system’s integrated sensors continuously monitor humidity, and when it reaches the so-called dew point, the cooling circle is automatically regulated to avoid condensation. Traditional (split system) air-conditioning appliances are not used.

Ventilation system:

Extract fans are installed in baths and toilets and storage rooms where natural ventilation is not provided. Kitchen extract fans are connected to sub-collector pipe system with no-return valve.

Metering consumption:

The consumption of hot- and cold water, heating, electricity can be metered and calculated separately for each apartment. The sub meters are centrally registered; entry into the apartments is not required to read them.


3 pieces of 230 Voltage electrical sockets are installed in every room, 4 in the living room, 6 in the kitchen (for the extract fan, refrigerator, dishwasher and 3 above the kitchen counter), 2 in the bathrooms (for the washing machine and 1 extra, and 1 in the corridors, and one ceiling lamp socket for each room. Balconies are going to have one socket and one side-wall or ceiling lamp and lampshade (not customisable), with interior switch. The façade lighting is constructed according to the plan, in the same appearance (not customisable). In addition to the previously mentioned, a counter lighting connection is going to be installed in the kitchen and a mirror lighting in the bathroom. Modern and well-designed electric accessories are going to be used in the apartments. The lighting bodies of the apartments are not part of the basic equipment, the Buyers have to ensure them (of course, the necessary wiring and switches will be provided). Each apartment will have 1*32A electric power.

Every living room will have at least one cable socket for TV, telephone and computer connections, considering the furniture plan.

Protective piping for a motion-activated alarm system shall be installed in apartments with internal garden access, in all rooms with windows, and in the upstairs apartments to monitor the entrance door and the terrace connected rooms.

Smart home system

To configure, program and remote-control devices, a personal computer or smart phone or tablet as well as internet connection are required. The remote-switchable devices can be controlled in a conventional manner, locally, independent from the smart home system  (lamp switch, socket, thermostat).

Central unit: this device is located above the entrance door in the lobby.

To control from an external location, internet connection of the router is necessary, which is to be provided by the Buyer.

Tablet: 10” Android tablet with pre-installed and pre-set smart home control software.

Smart sockets: 3 per apartment. Programmable, remote on/off, status and periodic consumption report, optical display of current consumption.

  1. Customisation options

The deadlines for modification and choice of materials for the apartment have expired and have been ordered from the main contractor by the investor, so the buyer has no possibility to make changes. Information on the selected materials can be obtained from the sales colleagues. The design of the façade and common parts of the building and the garden are entirely the responsibility of the Developer and we cannot accept any requests for changes. The common parts in this respect include the external windows, entrance doors and fittings, terrace cladding, staircase and stair coverings, balcony railings, terrace wall colours, electrical and other fittings (e.g. doorbells) in the staircase and balconies, and light fittings.

Not included in the purchase price:

Decorative elements of the tiling (central decor, border, etc.), bathroom fittings (mirrors, soap dish, etc.), light fittings, cornices, other built-in furniture.

The developer reserves the right to modify the listed materials – in terms of materials used, building structures, equipment and appliances-  to a technically equivalent or better quality.